McDATA 1U Server Manual de servicio Pagina 175
- Pagina / 430
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Maintenance Analysis Procedures
3-55
Maintenence Analysis Procedures
Was the maintenance action successful?
NO YES
↓ The fabric, ISL, and product are operational. Exit MAP.
Contact the next level of support. Exit MAP.
14
An E_Port segmented (operational product) because a response
(hello timeout) to a verification check indicates an attached switch is
not operational.
a. Perform a data collection at the operational product and send the
CD to support personnel for analysis. This information may
assist in fault isolating the failed switch.
b. Go to
MAP 0000: Start MAP
and perform fault isolation for the
failed switch. Exit MAP.
15
A product E_Port is connected to an unsupported fabric element.
Advise the customer of the problem and disconnect the ISL to the
unsupported fabric element. Exit MAP.
16
Event code is informational only and indicates a product E_Port is
fenced (blocked). An application or hardware malfunction occurred
(as indicated by failure symptoms or primary event codes) or the port
fencing policy is too restrictive. Obtain supplementary event data as
follows:
a. At the
Event Log
, examine the first five bytes (0 through 4)of
event data.
b. Byte 0 specifies the E_Port reporting the problem. Byte 4
specifies the port fence code as listed in Tabl e 3 -1 5.
Table 3-15 Port Fence Codes and Actions
Byte 4 Port Fence Code Action
01 Protocol error. Go to step 17.
02 Link-level hot I/O. Go to step 18.
03 Security violation. Go to step 19.
- Intrepid 1
- 6140 Director 1
- Printed July 2005 2
- Seventh Edition 3
- Contents 5
- Chapter4 RepairInformation 7
- Appendix A Event Code Tables 9
- Glossary 10
- General Information 23
- Director Description 23
- Field-Replaceable Units 26
- Power/System LED 27
- Assembly 27
- CTP Card 27
- UPM Card 29
- XPM Card 30
- SFPandXFPTransceivers 31
- Power Supply 32
- Fan Module 33
- SBAR Assembly 33
- AC Module 33
- Backplane 34
- Tools and Test Equipment 37
- Torque Tool and Hex Adapter 38
- Door Key 38
- Loopback Plug 38
- Tools Supplied by 39
- Service Personnel 39
- Director Management 40
- Installation Task Summary 45
- Desktop Installation 48
- Rack-Mount Installation 50
- (Optional) 53
- Configure Date and Time 55
- Configure Parameters 56
- Parameters View 57
- Configure Network Information 60
- Configure Port BB_Credit 62
- Configure Port NPIV 63
- SNMP View 64
- Enable CLI 65
- Configure SSL Encryption 66
- Install PFE Keys (Optional) 67
- (installed) or a red 69
- Configure Password 78
- Add a New User 84
- Change User Properties 85
- Add User Dialog Box 89
- Task 16: Configure PFE Key 93
- New Feature Key Dialog Box 95
- Configure Director Parameters 98
- Configure Fabric Parameters 100
- Installation Tasks 101
- Configure Ports 102
- Configure SNMP 103
- Configure Threshold Alerts 104
- Configure Security 110
- Configure Interswitch Links 111
- InCD Icon (Unformatted CD) 113
- McDATA Filecenter Home Page 118
- Maintenance Analysis 121
- Procedures (MAPS) 121
- Factory Defaults 121
- Quick Start 122
- MAP 0000: Start MAP 128
- ↓ Go to step 7 129
- ↓ Go to Table 3-3. Exit MAP 132
- Table 3-4 MAP 100 Event Codes 133
- RRP: Power Supply 134
- Event Log 136
- RRP: Backplane 137
- RRP: CTP Card 137
- RRP: SBAR Assembly 137
- RRP: Fan Module 138
- ↓ Go to step 11 143
- ↓ Go to step 13 144
- Installing or Upgrading 145
- Software on page 4–47 145
- Downloading Director 145
- Table 3-8 MAP400:EventCodes 150
- Collecting 151
- Maintenance Data 151
- Collecting Maintenance Data 152
- Table 3-9 MAP500:EventCodes 154
- XX:XX:XX:XX:XX:XX:XX:XX 156
- Performing Loopback Tests 164
- Blocking and Unblocking Ports 166
- Element Manager interface) 168
- Port List View 170
- Properties 170
- McDATA EFCM Basic 176
- Edition User Manual 176
- Cannot Merge 179
- Repair Information 181
- Procedural Notes 182
- Obtaining Log Information 183
- Element Manager Logs 185
- EFCM Basic Edition Logs 188
- Port LED Diagnostics 191
- Port Properties Dialog Box 195
- Port Technology Dialog Box 197
- Port Diagnostics Dialog Box 202
- Diagnostics View 205
- Swapping Ports 209
- Swap Ports Dialog Box 210
- System Files View 213
- Power-On Procedure 214
- Power-Off Procedure 215
- Set Online State Dialog Box 217
- Switch View 217
- Clean Fiber-Optic Components 221
- Firmware Library Dialog Box 224
- Firmware Upgrade View 226
- Managing Configuration Data 230
- Discover Setup Dialog Box 232
- Address Properties Dialog Box 233
- Backup Configuration View 234
- Restore Configuration View 235
- Removal and 237
- Replacement Procedures 237
- Removing and Replacing FRUs 239
- ESD Grounding Points 240
- Concurrent FRUs 241
- Nonconcurrent FRU 241
- RRP: AC Module 262
- Illustrated Parts 283
- Breakdown 283
- Front-Accessible FRUs 284
- Rear-Accessible FRUs 286
- Illustrated Parts Breakdown 288
- Miscellaneous Parts 289
- Table 6-4 Miscellaneous Parts 290
- Power Cords and Receptacles 291
- Event Code Tables 295
- CTPCardEvents(400through499) 332
- SBAR Events (600 through 699) 355
- Director Specifications 367
- Shipping and 368
- Environment 368
- Operating 368
- Fabricenter 369
- Equipment Cabinet 369
- Service Clearances 369
- Management Server and 371
- Ethernet Hub 371
- Management Server Description 371
- Ethernet Hub Description 372
- 24-Port Ethernet Hub 373
- Restore Management 375
- Requirements 375
- Restore Management Server 376
- Run Dialog Box 377
- Log On to Windows Dialog Box 380
- Safety Notices 383
- (Multi-Lingual 383
- Translations) 383
- NUMERICS 391
- Numerics 417
Relacionado con productos y manuales para Servidores McDATA 1U Server
Servidores McDATA 1U Server Manual de servicio
(316 paginas)
(316 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales